Velleman HAA2866 Instrukcja Instalacji

D I G I TA L AC C E S S CONTROL KEYPAD 3 OUTPUT RELAYHAA2866Programming & Installation ManualFOR ELECTRIC LOCK, INTER-LOCKAND SECURITY SYSTEM INS

THE ON-BOARD LED INDICATORS

FEATURE PROGRAMMING & OPERATION INSTRUCTIONSSET SYSTEM INTO PROGRAMMING MODE WITH THE MASTER CODE

REFRESH THE SYSTEM WITH THE “REFRESHING CODE” --- 9 9 9 9

KEYPAD PROGRAMMING MAKE SIMPLE – For General Users

6) Record an “EM Card + Commom User Code” to Operate The Output 1 for Door Open10 4 004 # (a) (b) (c) (d)

FEATURE PROGRAMMING -- KEY IN AND STORE THE DESIRED VALUES

Example: User Name Location Function Code User ID PIN/Code Card # Remark12345678910111213141516--1,000RECORD A MASTER CODE

OPERATION AND FUNCTIONS OF THE SUPER USER PIN

03 #RECORD-DELETE PINS OR CARDS FOR OUTPUT 1, 2, & 3 (Locations 10, 20 & 30)

Put the EM card close to the reader. Two-beep confirms the reading and 30 seconds waiting time is given for the entry of the User PIN, the Amber LED k

TABLE OF CONTENTSINTRODUCTIONFEATURESSPECIFICATIONSINSTALLATIONPrecautionsPackage ContentsCONNECTION TERMINALSThe On-Board LED IndicatorsThe Pacifier

4) Example 4 -- EM Card + Common User PIN :i) Programming :10 4 003 # (a) (b) (c) (d) (e)(a) (b) (c

Operation : (while the system is in the operation mode) # (a) (b) (c)(a) (b) (c) NOTE: The Duress Event can not b

Example 3: Delete a “Visitor Code” from Vistor ID 02 in the memory 40 02 # (a) (b) (c)(a) Visitor Code Programming, (b) The Visito

Example 2: Set a “Duress Code” with the number of “2 3 9 8 0” for Output 242 01 23980 # (a) (b) (c)

CONFIGURATION OF THE OUTPUT MODES OF OUTPUT 1, 2 AND 3 (Locations 51, 52 & 53)

USER PIN ENTRY MODE – Auto or Manual (Location 70)

STATUS LED FLASHING ON-OFF DURING STANDBY (Location 73)

INTELLIGENT EGRESS BUTTON – AN UNIQUE FEATURE OF A CONTEMPORARY KEYPAD

EGRESS DELAY , WARNING AND ALARM (Location 90)

EXAMPLES:Example 1: Set Egress Button in Momentary contact 5 seconds with delay & warning beep90 2 5 # (a) (b)

Split-decoded Keypad SystemThe Wire HarnessThe Operation Modes and The Wiegand Output Wiegand Output at Keypad Operation ModeTIMING & ELECTRICAL M

THE WIRE HARNESS FOR “WIEGAND DATA OUTPUT” & “APO DATA I/O”

30THE OPERATION MODES AND THE WIEGAND OUTPUT (Location 94)

TIMING & ELECTRICAL MANNER OF THE WIEGAND DATA OUTPUTWiegand is a commonly used interface between readers and control panels used in access contro

32THE 26 BIT WIEGAND DATA OUTPUT FROM THE EM CARDSThe Wiegand protocol for card reading has 1 first parity bit, 24 bits of the Card ID, and 1 stop bit

33THE 34 BIT WIEGAND DATA OUTPUT FROM THE ENTRY OF USER PINSWiegand is also a commonly used interface between keypad with user PINs and control panels

34THE APO DATA I/O PORT -- FOR SETTING UP A SPLIT-DECODED KEYPADThe information here is for setting up the keypad unit with an optional “Digital Keypa

35PROGRAMMING SUMMARY CHARTLOCATIONFUNCTIONENTRY LIMITS & CODE OPTIONSCODE ENTRYFACTORY DEFAULT0 1Master Code 4-8 Digits01 MASTER CODE #NIL0 2Supe

368 0Door Forced Open Warning & TimeFUNCTION MODE / TIME:0---OFF1-999 Seconds80 FUNCTION / TIME #Mode = 0, Door Forced OpenWarning OFF8 1Propped-u

37APPLICATION EXAMPLES

382) BASIC WIRINGS OF A STAND ALONE DOOR LOCK WITH INHIBIT AUTHORIZATION CODEUse output 3 as authorization control. The owner may key in the user code

Erratum p. 23 Section Configuration of the output modes on page 23 contains an error and should be as follows: Set timing mode for output relay Exampl

39An inter-lock system needs two door controllers. This application example uses two HAA2866 with simple cross wire connection on their "Output 1

40APPLICATION HINTS FOR THE AUXILIARY TERMINALS

41The Duress Output switches to (-) ground when duress code is entered. You may use it to turn ON an LED lamp and/ or a small buzzer to notify a guard

42Use the Normally Open (N.O.) output contact to shunt a Normally Closed (N.C.) protection zone of an alarm system.Set output contact to Start / Stop

43APPENDIXDRY CONTACTA dry contact means that no electricity is connected to it. It is prepared for free connections. The Relay Output contacts provid

VellemanSince its felectronicAll our proIn order tcheck, boorganisatoccur, pleGeneral • All consand defec• Vellemarefund therepair or proportionYou wi

INTRODUCTION

SPECIFICATIONS

INSTALLATION

CONNECTION TERMINALS

12 : OUTPUT 3 (NPN Transistor Open Collector Output)An NPN transistor open collector output that is controlled by the Group 3 User PINs or Cards for O