Velleman К8082 Instrukcja Użytkownika

"Safe" - style code lock K8082 ILLUSTRATED ASSEMBLY MANUAL H8082IP-1 Total solder points: 117 Difficulty level: beginner 1  2 3 4 5 

10  Make sure to connect all jumper wires with the display print and solder them (see figure 4.0). Assembly Fig. 4.0 Main PCB Disp

11 Assembly  Place the unit onto the front panel (fig. 6.0)  Fasten the potentiometer  Slide the black plastic knob on the axe and

12  Carefully solder the 4 PCB pins to the front panel.  Watch the position of the display! Fig. 8.0 Assembly

13 Connection diagram & example (4) CONNECTION DIAGRAM & EXAMPLE To e.g. alarm system NO COM NC+ -12VDC24V/3Amax.C4R2C7C1D1RY1SK1SK4VR1NONC12

14 (5) ENTER YOUR CODE Entering the code At first turn-on, the unit responds to factory code (1 - 0 - 1 - 0) only. To compose the code: 1) turn cl

15 Menu options Remark: you can only access the menu when the output relay is off  Hold the button to enter the setup menu  The display shows &apo

16 Menu options 'c' continuous mode : The output relay remains activated until the knob is turned. To set continuous mode:  Release b

17 'I'  Relay turns on at power up You have 1 min to enter your code (Display shows an animation)  Compose your code If the correct cod

18 (6) Schematic diagram. Schematic diagram

19 PCB (7) MAIN PCB 21gfedba+5VgndSETNO COM NC+ -12VDCVelleman P8082'124V/3Amax.C4C3R5R4R3R2R1C7C1C2C5C6D1D2IC1RY1SK1SK4SW1T1VR11C1 C2COMNONCSe

2 Features:  codelock with rotary encoder and 7-segment display  4-digit code  several operating modes  adjustable pulse duration  application e

Modifications and typographical errors reserved © Velleman Components nv. H8082IP'1 - 2006 (rev 1.0) VELLEMAN Components NV Legen Heirweg 33 9890

3 Assembly hints 1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project s

4 Assembly hints 1.3 Soldering Hints : 1- Mount the component against the PCB surface and carefully solder the leads 2- Make sure the solder j

5  R1 : 10K (1 - 0 - 3 - B)  R2 : 10K (1 - 0 - 3 - B)  R3 : 1K (1 - 0 - 2 - B)  R4 : 10K (1 - 0 - 3 - B)  R5 : 4K7 (4 - 7 - 2 - B)

6 Construction main PCB  C6 : 10µ F/50V  C7 : 470µ F/25V 9. Electrolytic Capacitors. Watch the polarity ! C...  RY1 : VR15M121C 1

7 (2) DISPLAY Setup:Velleman: 1m. timer/1o: 1m. timer/0d: defaultS: set codec: cont.t: timercwccw 0cw 1ccw 0cw 1code:defaultf.gedcbaenc2 enc1+5V21.

8 Assembly  Mount the jump wires onto the main PCB according to figure 1.0. . (3) ASSEMBLY Fig. 1.0

9 Assembly  Mount 4 print tabs onto the display print (see figure 2.0).  Assemble the unit together (fig. 3.0) Fig. 2.0 M3 Nut 10